MNR35 resistors 1/4 chip resistor networks MNR35 (3216 5 size) ! ! ! ! features 1) common terminals yield area 40% smaller than that of the mnr38. 2) 8-element construction makes the MNR35 ideal for bus line pull-up / pull-down. 3) convex electrodes easy to check the fillet after soldering is finished. 4) compatible with a wide range of mounting equipment. squared corners make it excellent for mounting using image recognition devices. 5) rohm resistors have approved iso-9001 certification. design and specifications are subject to change without notice. carefully check the specification sheet supplied with the product before using or ordering it. ! ! ! ! ratings item conditions specifications 0.063w (1 / 16w) rated power rated voltage operating temperature nominal resistance power must be derated according to the power derating curve in figure 1 when ambient temperature exceeds 70 c. ? 55 c~ + 125 c at 70 c the voltage rating is calculated by the following equation. if the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. e: rated voltage (v) p: rated power (w) r: nominal resistance ( ? ) e = p r limiting element voltage 50v 0 20 40 60 80 100 ? 55 0 70 100 125 ambient temperature ( c) power load (%) fig.1 see table 1. j ( 5%) 15 r 100k (e12) 200 resistance tolerance resistance range ( ? ) resistance temperature coefficient (ppm / c) table 1 ? ? ? ? before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level lo ads), be certain to evaluate the component in the mounted state. in addition, the reliability and performance of this component cannot be guaranteed if it is u sed with a steady state voltage that is greater than its rated voltage.
MNR35 resistors 2/4 ! ! ! ! characteristics item test conditions (jis c 5201-1) resistance variation of resistance with temperature solderability damp heat, steady state endurance at 70 c endurance rapid change of temperature bend strength of the end face plating resistance to solvent resistance to soldering heat overload jis c 5201-1 4.5 jis c 5201-1 4.8 measurement : ? 55 / + 25 / + 125 c jis c 5201-1 4.18 soldering condition : 260 5 c duration of immersion : 10 1s. jis c 5201-1 4.24 40 c, 93%rh test time : 1,000h~1,048h resistor type guaranteed value (2.0% + 0.1 ? ) (1.0% + 0.05 ? ) (3.0% + 0.1 ? ) j : 5% see table.1 no remarkable abnormality on the appearance. a new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. without mechanical damage such as breaks. (3.0% + 0.1 ? ) (3.0% + 0.1 ? ) (1.0% + 0.05 ? ) (1.0% + 0.05 ? ) (1.0% + 0.05 ? ) jis c 5201-1 4.25.1 rated voltage (current), 70 c 1.5h : on ? 0.5h : off test time : 1,000h~1,048h jis c 5201-1 4.25.3 125 c test time : 1,000h~1,048h jis c 5201-1 4.29 23 5 c , immersion cleaning, 5 0.5min. solvent : 2-propanol jis c 5201-1 4.19 test temp. : ? 55 c ~ + 125 c 5cyc jis c 5201-1 4.33 jis c 5201-1 4.17 rosinethanol (25%wt) soldering condition : 235 5 c duration of immersion : 2.0 0.5s. jis c 5201-1 4.13 rated voltage (current) 2.5, 2s. limiting element voltage 2 : 100v ! ! ! ! external dimensions (units : mm) material thick dielectric glaze of ruthenium thick film of silver for primary electrode nickel-coated secondary electrode external electrode coated with sn/pb or sn alumina substrate overcoating cross section b-b' cross section a-a' 6.4 0.4 ? 1.27 0.55 0.1 0.5 0.2 0.8 0.2 1.0 0.2 3.1 0.2 0.5 0.3 max.0.5 b b' a' a r103 ? pitch of the upper electrode . 1 1 1 1 1 1 2 2 2 3 3 4 4 5 5 5 6 6 6
MNR35 resistors 3/4 ! ! ! ! equivalent circuit r8 r2 r7 r3 r6 r4 r5 r1 r1 = r2 = r3 = r4 = r5 = r6 = r7 = r8 ! ! ! ! packaging 0 2 0 4 0 6 0 8 0 2 0 4 0 6 0 8 c abd label abcd 13 0.3 13 0.2 reel taping a 0 p 1 p 0 p 2 b 0 f w k e d 0 180 0 ? 3 60 + 1 0 eiaj et-7200a compliant (units: mm) (units: mm) wf ea 0 b 0 d 0 p 0 p 1 p 2 k 12.0 0.3 5.5 0.05 1.75 0.1 3.4 0.1 6.6 0.1 4.0 0.1 4.0 0.1 2.0 0.05 1.0 0.15 1.5 + 0.1 0 ! ! ! ! product designation code j5 MNR35 taping embossed reel part no. packaging package style j 5% 3-digit iec coding system packaging / processing specifications r MNR35 circuit configuration code resistance tolerance nominal resistance part no.
MNR35 resistors 4/4 ! ! ! ! electrical characteristics ? 6.0 ? 5.0 ? 4.0 ? 3.0 ? 2.0 ? 1.0 0 2.0 1.0 4.0 3.0 6.0 5.0 resistance ( ? ) fig.2 resistance dc resistance (%) jis c 5201-1 4.5 sample size : n = 40pcs 20 c 65%rh 10 100 1k 10k 100k ? 400 ? 300 ? 200 ? 100 0 100 200 300 400 resistance ( ? ) fig.3 variation resistance with temperature temperature coefficient (ppm / c) jis c 5201-1 4.8 sample size : n = 16pcs 25 c / ? 55 c 25 c / 125 c 15 100 1k 10k 100k ? 4.0 ? 6.0 ? 2.0 0 2.0 4.0 6.0 resistance ( ? ) fig.4 overload ? r/r (%) jis c 5201-1 4.13 sample size : n = 16pcs rated voltage 2.5times 2s limiting element voltage 2 : 100v 10 100 1k 10k 100k ? 2.0 ? 3.0 ? 1.0 0 1.0 2.0 3.0 resistance ( ? ) fig.5 resistance to soldering heat ? r/r (%) jis c 5201-1 4.18 sample size : n = 16pcs soldering condition : 260 c 10s 10 100 1k 10k 100k ? 2.0 ? 3.0 ? 1.0 0 1.0 2.0 3.0 resistance ( ? ) fig.6 rapid change of temperature ? r/r (%) jis c 5201-1 4.19 sample size : n = 16pcs ? 55 c / 125 c 5cyc 10 100 1k 10k 100k ? 4.0 ? 6.0 ? 2.0 0 2.0 4.0 6.0 resistance ( ? ) fig.7 damp heat, steady state ? r/r (%) jis c 5201-1 4.24 sample size : n = 16pcs 40 c 93%rh with no load 1,000h 10 100 1k 10k 100k ? 4.0 ? 6.0 ? 2.0 0 2.0 4.0 6.0 resistance ( ? ) fig.8 endurance at 70 c ? r/r (%) jis c 5201-1 4.25.1 sample size : n = 16pcs 70 c 1,000h overload : the rated voltage 10 100 1k 10k 100k ? 4.0 ? 6.0 ? 2.0 0 2.0 4.0 6.0 resistance ( ? ) fig.9 endurance ? r/r (%) jis c 5201-1 4.25.3 sample size : n = 16pcs 125 c with no load 1,000h 10 100 1k 10k 100k ? 2.0 ? 1.5 ? 1.0 ? 0.5 0 0.5 1.0 1.5 2.0 resistance ( ? ) fig.10 resistance to solvents resistance change (%) jis c 5201-1 4.29 sample size : n = 16pcs ipa, 5min. 15 100 1 k 10k 100k
|